MIAOXUE builds its 10 ton knuckle boom in three configurations. A 10 ton knuckle boom crane is a truck mounted crane with a folding hydraulic boom whose maximum rated load, 10,000 kg, applies only close to the column. Our SQ10ZA4, SQ10ZA5 and SQ10ZA6 share that rating, a 21 t·m lifting moment, 360° slewing and an identical hydraulic specification, so the real difference is the number of hydraulic boom sections. Maximum reach is 10.495 m, 12.63 m and 14.68 m respectively, and the rated load at full reach falls from 1,880 kg to 1,480 kg and 1,150 kg. Meanwhile, the crane’s own weight rises from 3,350 kg to 3,550 kg and 3,700 kg. The practical rule is therefore simple: choose the shortest boom that comfortably reaches your furthest regular set-down point. Complete drawings for each configuration are on the 10 ton knuckle boom truck mounted crane page.
We have manufactured truck mounted cranes in Xuzhou since 2003, and the 10 t class is one of the capacities international buyers ask about most often. This November 2026 revision of our February announcement replaces the earlier general marketing language with verified figures from our current dimension drawings and load charts.
Key takeaways
- “10 ton” is the rated load close to the column, at 2 m, whereas at full reach the three configurations lift between 1,150 kg and 1,880 kg.
- The SQ10ZA4, SQ10ZA5 and SQ10ZA6 have 3, 4 and 5 hydraulic boom sections, and each additional section adds approximately 2 m of reach.
- At the same radius the three lift almost identical loads, although the SQ10ZA4 is 50 to 80 kg ahead at matching chart points.
- A longer boom increases crane weight to 3,550 kg for the SQ10ZA5 and 3,700 kg for the SQ10ZA6, compared with 3,350 kg for the SQ10ZA4, and that weight reduces the truck’s available payload.
- All three need 40 L/min at 30 MPa, about 30 kW, from the truck’s power take-off, and share the same 2,310 to 5,610 mm outrigger span.
What does “10 ton” mean on a knuckle boom crane?
It is the maximum rated load, and a crane achieves it only at its shortest radius. In OSHA’s definition, rated capacity is “the maximum working load permitted by the manufacturer under specified working conditions” [1]. Those conditions typically include “equipment configuration, radii, boom length, and other parameters of use”. The working radius is the horizontal distance from the slewing centre to the hook. On our 10 t knuckle booms, the 10,000 kg rating applies at a radius of 2 m, while at approximately 4.5 m the permitted load is already below half of that figure. Our guides to the crane safe working load and how to read a crane load chart explain the rest.
SQ10ZA4 vs SQ10ZA5 vs SQ10ZA6: the numbers that decide
Knuckle boom cranes are hydraulically powered articulated arms fitted to a truck or trailer, whose jointed sections fold into a small space when the crane is not in use. The same machine is also called a loader crane or articulating crane [2]. In our model code, SQ10 identifies the 10 t class and Z the knuckle boom. A4, A5 or A6 gives the number of boom sections, meaning one main boom plus 3, 4 or 5 hydraulic extensions. The table compares only the figures that actually change a buying decision.
| Figure | SQ10ZA4 | SQ10ZA5 | SQ10ZA6 |
|---|---|---|---|
| Boom sections | 1 main + 3 hydraulic | 1 main + 4 hydraulic | 1 main + 5 hydraulic |
| Maximum reach | 10.495 m | 12.63 m | 14.68 m |
| Lifting height (load chart) | about 13 m | about 15 m | about 17 m |
| Rated load at 2 m | 10,000 kg | 10,000 kg | 10,000 kg |
| Rated load near 4.5 m | 4,700 kg at 4.44 m | 4,650 kg at 4.506 m | 4,650 kg at 4.5 m |
| Rated load near 8.5 m | 2,350 kg at 8.445 m | 2,280 kg at 8.51 m | 2,280 kg at 8.51 m |
| Rated load at full reach | 1,880 kg | 1,480 kg | 1,150 kg |
| Crane self weight | 3,350 kg | 3,550 kg | 3,700 kg |
| Length along the chassis | 1,076 mm | 1,076 mm | 1,199 mm |
| Stowed height | 2,340 mm | 2,340 mm | 2,340 mm |

The chart reveals two important patterns. First, at the same radius the three configurations lift almost identical loads, although the SQ10ZA4 carries 50 to 80 kg more at matching chart points. Second, every additional boom section adds approximately 2 m of reach, and the SQ10ZA6 is the only configuration that still lifts at 14.68 m. That extra reach adds crane weight, because the SQ10ZA5 is 200 kg heavier than the SQ10ZA4 and the SQ10ZA6 adds another 150 kg.
Which 10 ton knuckle boom configuration fits which job?
Begin with the location where the load must land, not with the tonnage. Measure the distance from the crane’s slewing centre to your usual set-down point, then add a realistic margin for the parking position you will actually get on a busy street or construction site.
SQ10ZA4: heavy loads close to the truck
The SQ10ZA4 suits work where the load lands within about 10 m of the crane. Typical jobs include loading and unloading heavy items such as steel sections, precast concrete components, machinery and equipment onto the truck’s own bed or a trailer alongside. For example, a machinery dealer moving equipment between a yard and a customer’s workshop rarely needs more reach. It is the lightest of the three configurations, so it leaves the most payload available, and it lifts the most at 10.5 m.
SQ10ZA5: the all-round building-supply reach
The SQ10ZA5 adds a fourth hydraulic section for 12.63 m of reach. It suits building-supply deliveries such as blocks, bricks, palletised materials and reinforcing steel, placed over a site fence, a footpath or a row of parked vehicles where the truck cannot get close. Even at full reach, it still lifts 1,480 kg.
SQ10ZA6: the longest reach and height
The SQ10ZA6 reaches 14.68 m and about 17 m high on its load chart. It is the logical choice when materials travel deep into a site, onto a roof or to an upper floor, and lighter loads at long reach form the daily work. It requires 1,199 mm of chassis length behind the cab instead of 1,076 mm, and it weighs 3,700 kg.
Example scenario: steel bundles over a footpath
Example scenario (an illustration, not a customer record): a steel stockholder delivers rebar bundles. Each bundle weighs an ASSUMED 1,700 kg, and the slings add an ASSUMED 50 kg, so 1,750 kg hangs on the hook. At most delivery addresses the driver can only park with the set-down point 11 m from the slewing centre, which immediately eliminates the SQ10ZA4, because its maximum reach is 10.495 m.
On the SQ10ZA5 chart, 11 m falls between 10.56 m (1,800 kg) and 12.63 m (1,480 kg). We always read the lower value, so 1,480 kg applies and the lift fails by 270 kg. If the driver parks so that the bundle lands within 10.56 m, the rating becomes 1,800 kg and the lift passes with only 50 kg to spare. That margin is uncomfortably thin, so lighter bundles, a closer parking position or the SQ10ZA4 with a shorter set-down distance are the safer alternatives. The SQ10ZA6 gives an identical answer at 10.56 m and adds 150 kg of crane weight, so it is only justified if several regular destinations require more than 12.63 m.
What truck does a 10 ton knuckle boom crane need?
Our drawings do not specify a chassis class or gross vehicle weight, because the correct truck depends on the vehicle itself, the crane position and the payload you need to carry. Consequently, the body builder sizes the truck from the crane’s figures. Our guide to selecting the tonnage of a truck mounted crane covers payload, and the truck mounted crane installation guide covers mounting. For a 10 t knuckle boom, these are the figures to send your body builder:
- Crane self weight: 3,350, 3,550 or 3,700 kg. Winch versions are about 70 to 110 kg heavier, confirmed with the quote.
- Length along the chassis behind the cab: 1,076 mm, or 1,199 mm for the SQ10ZA6.
- Outrigger span: 2,310 to 5,610 mm, with outrigger height 740 to 1,390 mm.
- Hydraulic supply from the power take-off: 40 L/min at 30 MPa, about 30 kW, with a 160 L oil tank.

MIAOXUE supplies the crane only. If you purchase the truck in China, the crane can be installed at our factory before shipping. If you purchase the truck locally, we ship the crane separately, a local body builder installs it, and our engineers support the installation remotely. Send us the truck make, model and wheelbase before ordering, and we will check that the chassis and power take-off suit the crane.
Knuckle or telescopic at 10 tons?
Many buyers search for a “10 ton boom truck” and could mean either type. A knuckle boom folds into a compact package behind the cab and can reach over a wall to position a load at a low angle. A telescopic crane lifts on a winch rope from a straight boom that extends in line. Our comparison of knuckle boom vs telescopic boom truck cranes covers the choice model by model, and the straight-boom option in this class is the 10 ton telescopic boom truck mounted crane.
Winch, remote control, attachments and marine versions
Each configuration is also available with a winch, designated SQ10ZA4J, SQ10ZA5J and SQ10ZA6J. The product page lists manual levers, an elevated operator seat or a wireless remote as operating options. A remote control lets the operator stand where the set-down point is clearly visible, as our article on truck crane remote control explains. Optional attachments include a hydraulic gripper, clamshell bucket, orange peel grab, timber grapple and auger. Their weight must be deducted from the load chart values, as our guide to knuckle boom crane attachments shows.
Every MIAOXUE crane is listed with a load moment limiter, as our article on the lifting moment of a crane explains. For vessels, marine versions of this class are drawn as the SQ10ZA5T, SQ10ZA5TJ and SQ10ZA6TJ, listed under knuckle boom marine cranes. The SQ10Z series holds a CE certificate under the EU Machinery Directive 2006/42/EC. As standard the crane lifts materials; a work basket for lifting people is an option, charged separately.
How do you choose between the three configurations?
- Measure the reach. Determine the distance from the slewing centre to your furthest regular set-down point, including a realistic margin for parking.
- Weigh the load. Add the weight of slings, forks or a grab to your heaviest regular load. OSHA’s crane rule says equipment “must not be operated in excess of its rated capacity” [3].
- Read the chart. Select the shortest boom whose chart covers that load at that radius, and between two chart points always use the lower value.
- Check the truck. Confirm the remaining payload after the crane’s weight, the mounting length and the power take-off capacity with your body builder.
Always keep the load chart available with the crane. OSHA requires the rated capacities and the operator’s manual to be “readily available in the cab at all times for use by the operator” [3], and the employer must follow “all manufacturer procedures”, including use with attachments.
Frequently asked questions
Can a 10 ton knuckle boom crane lift 10 tons at full reach?
No. Our three 10 t configurations lift 10,000 kg only at 2 m. At full reach the SQ10ZA4 lifts 1,880 kg at 10.495 m, the SQ10ZA5 1,480 kg at 12.63 m and the SQ10ZA6 1,150 kg at 14.68 m, with the boom horizontal.
How far and how high can a 10 ton knuckle boom crane reach?
Maximum reach is 10.495 m, 12.63 m or 14.68 m, depending on whether the boom has 3, 4 or 5 hydraulic sections, and the corresponding lifting heights on the load charts are approximately 13 m, 15 m and 17 m.
How much does a 10 ton knuckle boom crane weigh?
The crane weighs 3,350 kg as the SQ10ZA4, 3,550 kg as the SQ10ZA5 and 3,700 kg as the SQ10ZA6. Winch versions are approximately 70 to 110 kg heavier. This weight directly reduces the available payload of the truck on which it is installed.
Is a 10 ton knuckle boom crane the same as a 10 ton boom truck?
Not always. People frequently use “boom truck” for a truck carrying a telescopic crane, whereas a knuckle boom folds compactly behind the cab. Both are truck mounted cranes, and MIAOXUE manufactures both types in the 10 t class. We supply the crane, and the truck is supplied separately.
What hydraulic power does a 10 ton knuckle boom crane need?
All three configurations require 40 L/min at 30 MPa, approximately 30 kW, usually delivered by the truck’s power take-off. The crane also carries its own 160 L hydraulic oil tank.
How we compiled this guide
Every crane figure comes from the current MIAOXUE technical drawings, which we read on 18 November 2026. These are the SQ10ZA4 dimension drawing issued in November 2026 with its load chart, and the SQ10ZA5 and SQ10ZA6 dimension drawings and load charts. The boom-section count, winch weights, operating options and attachments come from the live product page. We took the definitions of articulating crane and rated capacity from 29 CFR 1926.1401, and the operating rules from 29 CFR 1926.1417, both on eCFR. The general description of loader cranes comes from Wikipedia. The scenario uses clearly marked assumed weights. Achord Chan, Product Operations Director, reviewed the guide. It does not replace the crane’s operator’s manual or the rules where you work.
Get the 10 t drawings for your truck
Tell us your heaviest regular load, the reach you need and the truck you plan to use. We will recommend the SQ10ZA4, SQ10ZA5 or SQ10ZA6 and send its dimension drawing and load chart. See all three on the 10 ton knuckle boom truck mounted crane page or browse all knuckle boom truck mounted cranes. Every crane carries a 12-month warranty on the whole machine, and common spare parts leave the factory within 48 hours. Contact us for a quotation.
